Alloy Guide Sheet Terms of Use

Use Good Design Principles

1. St. Paul Foundry is providing this information on metal characteristics for informational purposes only. Before making a final decision on alloy selection consider the following and all other appropriate design and specification principles. Please note that this is not an exhaustive list.

2. Consult the appropriate specification from an accredited specifying body (ASTM, SAE, Federal or Military) to determine current minimum values of this alloy.

3. Use appropriate design safety factors.

4. Use Failure Modes and Effects Analysis to help identify possible weaknesses in designs and specifications.

5. Use computerized stress analysis tools.

6. Use appropriate certification requirements for your casting suppliers. These may include test bars, chemical certifications, radiography, dye penetrant or other non-destructive testing methods.

7. Test your design to failure in a controlled environment. Then test it to failure in a simulation of its end use.

8. You and you alone are responsible for the suitability of your design and the materials that you select.

Disclaimer

WHILE EVERY EFFORT IS MADE BY ST. PAUL FOUNDRY (SPF) TO ENSURE ACCURACY, THIS INFORMATION IS PROVIDED FOR GENERAL INFORMATION PURPOSES ONLY AND NOT FOR ANY OTHER PURPOSE. BY ACCESSING THIS INFORMATION, YOU AGREE THAT IT MAY BE REVISED AT ANY TIME, IT IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, THAT NO WARRANTY OR REPRESENTATION IS MADE ABOUT ITS CONTENT OR SUITABILITY FOR ANY PURPOSE, AND THAT SPF EXPRESSLY DISCLAIMS WARRANTIES OF MERCHANTABILITY AND FITNESS. YOU ASSUME ALL RISK AND LIABILITY FOR ANY LOSS, DAMAGE, CLAIM, OR EXPENSE RESULTING FROM YOUR REVIEW, USE, OR POSSESSION OF THIS INFORMATION.



Skip Navigation Links713.0 Aluminum Zinc
St. Paul
Foundry
Banner
Great Castings          St. Paul Foundry 954 Minnehaha Ave West St. Paul MN 55104 651-488-5567 www.stpaulfoundry.com

 Simplifying the Supply Chain For High Knowledge Content Components
ISO 9001:2008  

713.0 Aluminum
Aliases
ANSI AA NUMBER 713.0
Common Name 613
UNS Designation A07130
Alias 713
Alias Tenzaloy
Nearest Applicable Casting Standards
AMS 4236
Specification Composition
Minimum Maximum
Silicon (Si) 0.25
Iron (Fe) 1.1
Copper (Cu) 0.4 1
Manganese (Mn) 0.6
Magnesium (Mg) 0.2 0.5
Chromium (Cr) 0.35
Nickel (Ni) 0.15
Zinc (Zn) 7 8
Titanium (Ti) 0.25
Other (Total) 0.25
Specification Properties
(Heat Treat 'F' Denotes As Cast) Heat Treat State Minimum
Tensile Strength (ksi) F 34
Yield Strength (.5% extension under load) (ksi) F 25
Elongation (2 inch gauge length) (%) F 5
Typical Properties
Heat Treat State Typical
Compressive Yield Strength (ksi) 25
Hardness (Brinell) (HB @ 500kg) 75
Shear Strength (ksi) 26
Endurance Limit (K ksi) 9
Modulus of Elasticity (K ksi) 9.7
Density (lb/cu.in. @ 68F) .100
Electrical Conductivity (% IACS @ 68F) 30
Thermal Conductivity (cal/sec/sq cm/cm/C @ 25C) 0.29
Coefficient of Thermal Expansion (per F @ 68-212F) 13.4
Coefficient of Thermal Expansion (per F @ 68-572F) 14.6
Melting Range (Liquidus-Solidus)(F) 1100-1180
Resistance to Hot Cracking F
Pressure Tightness F
Fluidity G
Solidification Shrinkage Tendency F
Strength at Elevated Temperatures F
Corrosion Resistance E
Machinability E
Polishing E
Gas Welding F
Arc Welding G
Brazing Yes
Normally Heat Treated No
Annodizing Appearance Light Yellow
Comments
Aging: Self age in 21-30 days
Applications
Arm
Arm In
Arm Outfeed
Decorative Castings
Farm Machinery
Hub Drive
Knob
Large Intricate Castings
Machine Tool Parts
Marine Castings
Nose
Pressure Roller
Shim
Ski
Water Tee
Great Castings
         St. Paul Foundry 954 Minnehaha Ave West St. Paul MN 55104 651-488-5567 www.stpaulfoundry.com
Banner
Banner
St. Paul Foundry
954 Minnehaha Avenue West
Saint Paul, Minnesota 55104
(651) 488-5567  Fax: (651) 488-0908
Sales: (651) 312-4734 email

Site Map      Copyright 2017

Alloy Guide Sheet Terms of Use

Use Good Design Principles

1. St. Paul Foundry is providing this information on metal characteristics for informational purposes only. Before making a final decision on alloy selection consider the following and all other appropriate design and specification principles. Please note that this is not an exhaustive list.

2. Consult the appropriate specification from an accredited specifying body (ASTM, SAE, Federal or Military) to determine current minimum values of this alloy.

3. Use appropriate design safety factors.

4. Use Failure Modes and Effects Analysis to help identify possible weaknesses in designs and specifications.

5. Use computerized stress analysis tools.

6. Use appropriate certification requirements for your casting suppliers. These may include test bars, chemical certifications, radiography, dye penetrant or other non-destructive testing methods.

7. Test your design to failure in a controlled environment. Then test it to failure in a simulation of its end use.

8. You and you alone are responsible for the suitability of your design and the materials that you select.

Disclaimer

WHILE EVERY EFFORT IS MADE BY ST. PAUL FOUNDRY (SPF) TO ENSURE ACCURACY, THIS INFORMATION IS PROVIDED FOR GENERAL INFORMATION PURPOSES ONLY AND NOT FOR ANY OTHER PURPOSE. BY ACCESSING THIS INFORMATION, YOU AGREE THAT IT MAY BE REVISED AT ANY TIME, IT IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTY, THAT NO WARRANTY OR REPRESENTATION IS MADE ABOUT ITS CONTENT OR SUITABILITY FOR ANY PURPOSE, AND THAT SPF EXPRESSLY DISCLAIMS WARRANTIES OF MERCHANTABILITY AND FITNESS. YOU ASSUME ALL RISK AND LIABILITY FOR ANY LOSS, DAMAGE, CLAIM, OR EXPENSE RESULTING FROM YOUR REVIEW, USE, OR POSSESSION OF THIS INFORMATION.